How To Replace A Tub (For Newbies).
How To Replace A Tub (For Newbies).
Blog Article
Just about everyone seems to have their own unique opinion on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is easily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have actually certified on your own for the work and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will assist you set up a new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the tub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has been made use of at the very least when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break a rigid seal, creating the water to permeate the wall surface between the bath and also the tiling, causing problems with wetness and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes and also cartridges, and are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our part on Installing A Bathtub. Thanks so much for taking time to read through our article post. I beg you take the time to share this blog post if you liked it. Bless you for your time. Don't forget to pay a visit to our blog back soon.
Source Report this page